ASSET CP2 Update – Sixth Edition: Aligning Cylinder Inspection and Testing with Current International, European and British Standards

ASSET CP2 Update – Sixth Edition: Aligning Cylinder Inspection and Testing with Current International, European and British Standards

Association of Scuba Service Engineers and Technicians
Standards • Technical Guidance • Training • Test Station Recognition

ASSET Technical Update

Published: 21 November 2026   |   CP2 Sixth Edition, Revision 0.4   |   Draft for Technical Review

ASSET has completed a substantial update to Code of Practice No. 2 (CP2), strengthening its standards references and setting out a clearer, more consistent framework for the periodic inspection and testing of metallic transportable gas cylinders.

Technician carrying out a visual examination of a metallic gas cylinder in a specialist workshop
Inspection work depends on sound technical judgement, suitable equipment, competent personnel and traceable records. Image: illustrative workshop scene.

Document status: The current working issue is ASSET CP2, Sixth Edition, Revision 0.4, dated 19 November 2026. It is marked Draft for Technical Review. It is not being presented as a finally validated or legally mandated document. The update is an important step in the technical review and modernisation of the ASSET framework.

Why has ASSET updated CP2?

Standards, technical practices and regulatory frameworks do not stand still. Since earlier editions of CP2 were issued, important cylinder, valve, quality-management and conformity-assessment references have been revised. Some older standards have been withdrawn or superseded, while new editions and amendments have been published.

Test Stations may still hold historic workshop manuals, procedures and forms that refer to older editions. A document can continue to be used for years after the technical reference it cites has changed. That creates a risk of inconsistent interpretation, outdated procedures and uncertainty about which requirements apply to a particular cylinder.

The Sixth Edition update is intended to address that problem. It modernises the Code’s reference register, clarifies how the applicable technical and legal route is identified, and strengthens the management controls that support safe, repeatable and traceable work.

Current standards references

Review and update references to relevant ISO, EN and BS publications, including their amendments and national adoptions.

Clearer technical scope

Define the cylinder types and activities covered, and identify where separate procedures and approvals are required.

Stronger station controls

Improve expectations for personnel competence, premises, equipment, calibration, procedures and quality assurance.

Better traceability

Make it easier to follow a job from receipt and cylinder identification through inspection, test, decision, certification and release.

A standards-based approach: ISO, EN and BS

ASSET’s approach is to work with the relevant International Standards (ISO), European Standards (EN) and British Standards (BS), including the correct national adoption where one exists. The reference used for an individual cylinder must still be selected according to its design approval, markings, service, legal route and jurisdiction.

One important principle runs throughout the revised CP2: a later-published standard does not automatically replace an edition that is specifically incorporated by legislation, an approval or a transport framework. The Test Station must identify the edition that actually applies, rather than simply selecting the newest publication or the most convenient procedure.

Standard / referenceSubject and relevance to CP2
BS EN ISO 18119:2018+A2:2024Periodic inspection and testing of seamless steel and seamless aluminium-alloy gas cylinders and tubes. This is the principal technical reference for the metallic cylinder scope addressed by CP2, within the standard’s scope and applicable legal route.
BS EN ISO 11623:2023Periodic inspection and testing of composite cylinders and tubes. Composite cylinders are outside CP2’s general metallic-cylinder scope and require a separate procedure and approval basis.
BS EN ISO 22434:2022Inspection and maintenance of gas-cylinder valves, including valves reused at periodic inspection, within the standard’s stated scope.
BS EN ISO 13341:2025Fitting valves to gas cylinders, including preparation and connection practices for the relevant ISO thread systems.
ISO 10297:2024Cylinder valve specification and type testing.
ISO 15245-1:2021; ISO 11363-1:2018+A1:2023; ISO 11363-2:2017Relevant valve/cylinder connection thread systems and associated gauges, where the actual connection design falls within their scope.
ISO 9712:2021; ISO 16810:2024Personnel qualification for industrial NDT and general principles for ultrasonic testing, where specialist NDT is required.
ISO/IEC 17025:2017Competence of testing and calibration laboratories, relevant to calibration and measurement traceability where applicable.
ISO 9000:2026; ISO 9001:2026Quality-management concepts and requirements referenced in the context of documented processes, responsibility, control and continual improvement.
BS EN ISO/IEC 17020:2026Requirements for bodies performing inspection. Relevant where an inspection-body accreditation or regulatory framework applies; CP2 does not make accreditation to ISO/IEC 17020 a universal condition for every Test Station.
BS EN ISO/IEC 17024:2026Requirements for bodies operating certification of persons. This is a personnel-certification reference, not a cylinder inspection or testing standard, and its inclusion does not mean ASSET or a Test Station is accredited to it.

The list above is a summary of selected references included in CP2’s Standards Reference Register. Not every standard applies to every cylinder or activity. The current controlled CP2 document and the relevant full standard, approval and legal requirements must be consulted before work is undertaken.

Understanding the role of EN and BS adoptions

ISO standards may be adopted at European level as EN ISO standards and then published nationally as BS EN ISO standards in the United Kingdom. Where this applies, the Test Station must verify the precise designation, edition, amendments and status of the national publication. The prefixes should not be treated as interchangeable by assumption; the applicable publication and legal incorporation must be checked.

CP2 therefore uses British and European adoptions where identified in its reference register, while retaining ISO references where that is the appropriate published designation. This helps Test Stations identify the technical source they are expected to use and avoids casual substitution of one edition or national designation for another.

Hydraulic test arrangements must be suitable for the cylinder, method and acceptance requirements being applied. Image: illustrative test-station scene.

What has changed in the Sixth Edition?

The updated CP2 retains a ten-section structure, but gives clearer direction on the systems and evidence expected from a Test Station operating within an ASSET-approved scope.

  1. Scope: defines the metallic transportable cylinder types covered by the Code, the 150-litre water-capacity boundary, and the need for separate approval routes for constructions outside the general scope.
  2. Test Station organisation: clarifies management and technical responsibility, workshop layout, separation of work status, safe gas discharge, access control and outsourced operations.
  3. Qualifications and training: strengthens expectations for task-specific competence, practical assessment, authorisation, visual capability and continuing competence.
  4. Equipment: identifies the equipment and facilities required for the approved activities, including handling, inspection, thread gauging, NDT where applicable, hydraulic testing, drying and valve service.
  5. Accuracy and calibration: sets out measurement control, master-gauge traceability, working-gauge comparison, calibration intervals and action where equipment is found out of tolerance.
  6. Documentation: clarifies controlled documents, booking-in records, individual cylinder worksheets, customer certificates and external service records.
  7. Quality assurance: strengthens workflow status identification, hold points, final release checks, independent review, internal audit and corrective action.
  8. Procedures: requires written sequential instructions for each activity within the Test Station’s approved scope, including safe handling and response to abnormal conditions.
  9. Records: clarifies record security, traceability, retention, electronic access and backup.
  10. Standards Reference Register: brings the referenced standards, regulations and supporting technical material into one structured section, with applicability determined for each cylinder and activity.

Technical safeguards built into the revised Code

No generic test values where the cylinder-specific requirement governs

CP2 does not invent universal test pressures, hold times, permanent-expansion percentages, wall-thickness limits, drying temperatures or defect-acceptance criteria. These must be established from the applicable cylinder approval, legal route, standard and manufacturer information. If the correct criterion cannot be established, the cylinder or activity is placed on hold and referred for a documented technical decision.

VET and PPT are treated as different test methods

Where hydraulic testing is required, the permitted method must be identified for the cylinder and its approval route. Volumetric expansion testing (VET) requires the relevant total and permanent expansion measurements and calculation. A proof pressure test (PPT) is assessed against its own pressure-hold, leakage and deformation requirements. Expansion figures must not be invented or inferred from a PPT result.

Blocked valves and zero-pressure verification

Valve removal is only undertaken after the cylinder has been safely depressurised and the zero-pressure state positively verified. A blocked or damaged valve requires a specific assessed procedure. Drilling, piercing, heating or uncontrolled intervention is not accepted as a routine way of gaining access. Where the risk cannot be controlled using available approved equipment and competence, the cylinder is isolated and referred.

Calibration and measurement traceability

Instruments used to accept or reject cylinders must be suitable for the measurement and decision. The Code calls for traceable calibration or verification, identified equipment status and records. It also includes a working-gauge comparison interval not exceeding one month against a suitable calibrated reference, subject to any stricter applicable requirement. Calibration intervals must be defined for each equipment category; the Code provides a normal maximum interval of 12 months for instruments directly affecting cylinder acceptance unless a shorter requirement applies.

Record retention and final release

Completed cylinder worksheets and associated records are to be retained for at least one complete periodic inspection and test interval (PIAT) plus one additional periodic inspection interval (PI), subject to a minimum of six years. A longer statutory, approval, contractual or competent-authority requirement takes precedence. A cylinder is not released while a required examination, test, assembly check, record or certificate review remains incomplete.

Ten supporting application and assessment forms

To make the Code practical for Test Stations, ASSET has developed a companion set of ten forms. Together they provide a structured way to submit information and evidence for review, and to record the outcome of an assessment.

FormTitlePurpose
AF-CP2-01Test Station ApplicationApplicant, site, responsible people and application details.
AF-CP2-02Scope of ApprovalCylinder families, services, activities, limitations and exclusions requested.
AF-CP2-03Premises and FacilitiesWorkshop layout, separation, gas discharge, safety and emergency arrangements.
AF-CP2-04Equipment and Measurement ControlEquipment capability, calibration, verification and measurement traceability.
AF-CP2-05Personnel Qualifications, Competence and AuthorisationTechnician qualifications, practical competence and authorised task scope.
AF-CP2-06Document Control, Quality Assurance and RecordsControlled documents, quality arrangements, record systems and retention.
AF-CP2-07Operating Procedures and Safe Systems of WorkWritten procedures, risk controls, hold points and stop-work arrangements.
AF-CP2-08Inspection, Testing and Cylinder Record ControlsInspection/testing method, cylinder-specific criteria and traceable work records.
AF-CP2-09Non-Conformity, Corrective Action and ComplaintsReporting, investigation, impact review, corrective action and complaint handling.
AF-CP2-10Test Station Assessment and Approval RecordASSET assessment findings, conditions, scope decision and review record.

The forms are designed to support a consistent application and assessment process. Completing an application does not automatically grant recognition or approval; the evidence must be reviewed and the ASSET decision recorded separately.

What CP2 recognition does — and does not — mean

ASSET recognition is a private technical scheme. It is not, by itself, a statutory licence, government approval, product certification, manufacturer authorisation, conformity-assessment accreditation or appointment as a legally designated inspection body.

A Test Station remains responsible for obtaining and maintaining any authorisation, accreditation or approval required by the law that applies to its location, activities and cylinder population. ASSET’s role is to define and assess the requirements of its own technical scheme and to make the basis and scope of recognition clear.

Equally, the inclusion of ISO/IEC 17020:2026 in the standards register does not make accreditation to that standard a universal requirement for every Test Station under CP2. It is relevant where the applicable inspection-body accreditation or regulatory framework requires it. ISO/IEC 17024:2026 concerns bodies that operate certification schemes for persons; it is not a cylinder periodic-inspection standard.

Keeping pace with regulatory and standards developments

CP2’s reference register also identifies the transport and pressure-equipment framework that may apply, including ADR, the European Transportable Pressure Equipment Directive (TPED) where applicable, relevant national implementing measures and workplace requirements.

At the date of this CP2 revision, ADR 2025 is the applicable published edition for the 2025–2026 cycle. The ADR 2027 amendments are scheduled to take effect on 1 January 2027. The Code highlights the need to check the effective ADR text and national implementation before work or carriage from that date. Where ADR 2025’s specified transition for EN ISO 11623:2015 applies to composite cylinders, that transition ends on 31 December 2026; the 2015 edition must not be relied on beyond the transition unless another applicable legal or approval basis expressly provides for it.

ISO has also advanced the next revision of ISO 18119 into the draft international standard process. The draft is not the published replacement standard. Until the new edition is formally published and becomes applicable through the relevant legal or approval route, draft provisions should be monitored but not treated as mandatory acceptance requirements.

What happens next?

Revision 0.4 is a working draft for technical review. Before final approval, ASSET must complete detailed validation against the licensed standards, relevant cylinder approvals and applicable legislation. Particular attention is required for cylinder-specific acceptance criteria, test pressure and hold conditions, expansion limits, drying parameters and regulatory transitions.

Following that review, comments and necessary corrections can be incorporated into a controlled revision. Test Stations should always use the current controlled issue and check that their own local procedures, equipment, personnel authorisations and records remain consistent with the scope for which they are recognised.

ASSET — supporting safe, competent cylinder inspection and testing

The CP2 update reflects ASSET’s commitment to clear technical requirements, current standards references, competent technicians and well-controlled Test Stations. For information about ASSET training, CP2 documentation or Test Station recognition, contact the Association.

Contact ASSET


Technical note: This article is an explanatory overview of ASSET CP2 Sixth Edition, Revision 0.4. It is not a substitute for the full text of the applicable standard, cylinder approval, legislation or manufacturer’s instructions. Standards are subject to change; always verify the current controlled publication and its applicability before undertaking inspection or testing.